Hydraulic storage tank lifting equipment is a kind of jack that uses a plunger or a hydraulic cylinder as a rigid jacking member. Simple lifting equipment is generally only equipped with a lifting mechanism to lift heavy objects.
Why do we maintain hydraulic storage tank lifting equipment in the right ways?
Why can't the hydraulic storage tank lifting equipment lift go up?
What are the advantages of hydraulic storage tank lifting equipment?
(1) The bottom of the hydraulic storage tank lifting equipment should be flat and tough when used. Oil-free planks to expand the bearing surface and ensure safety. Can not use iron plate instead of wood, to prevent sliding.
(2) When lifting, it is required to be stable. After the heavy object is lifted for a while, it is necessary to check whether there is any abnormality. If there is no abnormality, the roof can continue to be lifted. Do not lengthen the handle arbitrarily or operate it too hard.
Most of the hydraulic storage tank lifting equipment lift hydraulic power source is used for lifting and lowering operations. With the aging of the mechanical structure, some small faults will inevitably occur after long-term use, such as the lift does not lift, so what is the reason? The hydraulic lift cannot afford There are many reasons for the rise, the common ones are:
1. The load is too heavy, exceeding the rated load, and the load can be reduced.
2. The oil return valve is not closed, causing the hydraulic system to not work normally, and the oil return valve needs to be tightened.
3. The filter is blocked, replace or clean the filter.
4. If the hydraulic oil is insufficient, add enough hydraulic oil to the lift.
Main features of hydraulic storage tank lifting equipment:
1. The system consists of hydraulic pump station, oil cylinder, steel wire and stroke. Easy to install and operate;
2. The system adopts PLC central control to handle elevators. Each power pack is equipped with an auxiliary balance device to ensure the accuracy of simultaneous lifting;
3. The hydraulic lifting pump station has two operation modes: auxiliary manual control and central control. The cylinder can be adjusted to lift individually or in multiple groups, or in combination with multiple groups to achieve better precision and better welding effect;
4. All cylinders are equipped with safety valves. In the event of power failure, high-pressure hose rupture, burst, etc., it can be automatically locked to prevent the cylinder/fuel tank from falling.
With a large number of suppliers, we can choose the right suppliers according to customers' requirements and provide the most cost-effective products. WINCOO ENGINEERING CO., LTD provides big pressure vessel, heavy duty pressure vessel, industrial pressure vessel, automatic pipeline construction equipment, electric vertical tank construction solution, etc.
Plate rolling machine is a forging and pressing equipment.Plate rolling machine is mainly used in the field of cold machining of industrial containers and pressure tanks, etc.Required molding consistency, arcs are standard, good welding seam connection.Traditionally, industrial containers and tanks are formed by hand - by - hand, step - by - step, experience - operated roller.Due to the increasing demand for natural gas pipelines and oil tankers, traditional production has been unable to meet the requirements of the market.Fully automated machines are needed to realize large-scale industrial production.
II. Process analysis
Plate rolling process is a forming process that USES the plate rolling machine to make continuous 3-point bending of the plate. As shown in figure 1, the plate rolling process is composed of pre-bending -- centering -- coil circle --rounding
Plate rolling, plate at both ends of a length, because the plate did not contact the roller, not bending, which is called the remaining straight side.In order to avoid the plate from the work roll out, the actual residual straight edge is often larger than the theoretical value.Because the remaining straight edge is difficult to eliminate in the straightening, and causes a large weld stress and equipment load, easy to produce quality and equipment accidents, so the sheet material must be pre-bending the plate edge before rolling, so that the remaining straight edge is close to the theoretical value.
The purpose of centering is to make the workpiece busbar parallel to the roll axis to prevent the occurrence of skew.
3. Coil circle
The method of rolling the circle is divided into one feeding and multiple feeding.
The rebound of cold coiling is remarkable, and a certain amount of over coiling is needed.
Rounding is generally divided into three steps：
4.1.Loading.Adjust the roller to the required maximum corrected curvature according to experience or calculation;
4.2.Rounding.Roll the roller for 1-2 circles under straightening curvature (especially roll near the weld zone), so that the curvature of the whole circle is uniform;
4.3.Unloading.Gradually remove the load so that the workpiece rolls several times under gradually reduced corrective load.
III.Main structure and work principle
This machine is symmetrical rolling machine, down up roller and then let up and down roller do
opposite roll to bend steel plate.
B. This machine composed of two parts those are working part welded in whole chassis and moving part. Working part composed of left and right bearing base, one up roller, two bottom rollers (the material of the three rollers is 45#steel and do heat treatment), lifting screw and turbine and other accessory parts. Down rollers drive up roller to move, up roller can do up and down move by height way. Drive part composed of main motor, main speed reducer and other accessory parts.
C. Bottom rollers were drove by main motor through main speed reducer, output spindle of main speed reducer driven to two down rollers by one group gears, the revolve direction of rollers adjusted by main motor.
D. Upper roll lifted by accessory motor through vice speed reducer drive worm and worm wheel mechanism of right/left rolls bearing base. That to let the lifting pole do up and down move.
E. Unloading device is designed to remove the workpiece after drums bended into shape. Before unloading the upper rolls move to up limit position, the balance device on upper rolls ends hit upper rolls, draw out the spindle of the pin, then to remove the workpiece.
1.Universal upper roll rolling machine
2.Asymmetric plate rolling machine
3.Mechanical symmetrical plate rolling machine
4.Horizontal adjustable plate rolling machine
5.Four-rollers plate rolling machine
Simple chain type hydraulic jacking system is composed of one-stage double-acting hydraulic cylinder, pulley block, load-bearing chain and oil way etc. Moveable pulley is used to enlarge chain stroke, i.e. traveling distance of the cylinder is 1/2 of lifting distance of the chain. It applies to inverted installation and construction of various large storage tanks (steel) and various storage tanks.
LYT-type simple chain type hydraulic jacking system includes the following models: LYT-120-2700, LYT-200-2700, and LYT-300-2700 etc. (those with special stroke need to be customized).
What is the operation process of the simple chain type hydraulic jacking system?
What is the working principle of the simple chain type hydraulic jacking system?
What are the advantages of simple chain type hydraulic jacking system?
LYT-type simple chain type hydraulic jacking system is used to firstly lift the tank roof and the top (first layer) siding of the tank. It's required to group weld tank siding when the lifting height of siding exceeds the second siding (the second layer from the top) by 30-50mm, and group weld the third layer (the third layer from the top to the bottom) of the tank after lifting again, lift successively, group weld the siding of the tank layer by layer, until the last layer of siding.
LYT-type simple chain type hydraulic jacking system is used for lifting. When oil enters the hydraulic jack, the movable pulley is pushed upward by pressing the piston, thus driving the load-bearing chain to lift the expansion ring. In this way, the whole tank (including tank roof) is lifted up, until it reaches the pre-set height (there is a voidance of the next layer of plate). The siding in this layer is surrounded for butt welding. After the positioning block is welded, hydraulic hoist returns and the lift tank falls back to the newly-surrounded siding. After welding of circular seam and vertical seam, the door-type card for fixing expansion ring is cut off and the expansion ring is released. In this way, the hoist returns and expansion ring falls to the Model of hydraulic pump station Tank volume Rated pressure Rated flow Power Control voltage of solenoid valve Motor drive rate YB-7.2 220L (700*550*580) 25Mpa 7.2L/min Three-phase Four-wire (380V) 220V 5.5KW YB-14.5 340L (750*650*650) 25Mpa 14.5L/min 220V 7.5KW Mode of LYT-type hoist Rated lifting capacity (KN) Hydraulic area (mm) Rated oil pressure (MPa) Piston stroke (mm) Chain stroke (mm) Cylinder safety equipment Reinforcement measures LYT-120-2700 120 11304 25 1500 2700 Double-direction oil-way hydraulic lock 2 adjustable pull rods LYT-200-2700 200 18859.6 25 1500 2700 Double-direction oil-way hydraulic lock 2 adjustable pull rods LYT-300-2700 300 25434 25 1500 2700 Double-direction oil-way hydraulic lock 2 adjustable pull rods bottom of tank siding. Then, the next circular plate is expanded and transfer rib plate, such as door-type card, is welded for lifting, and so forth. The group welded tank is lift, until group weld of the last layer of siding, so that the whole storage tank is installed with this inverted method.
1. Simple chain type hydraulic jacking system is stable, safe and reliable. Due to the adoption of unified hydraulic control and single or partial (several) adjustment, the whole lifting process is relatively stable. The hoist is provided with synchronizing valve and hydraulic lock to prevent sliding and falling of the tank or heavy loads, which are caused by power failure and fracture of oil tube. Hydraulic lifting is stable, safe and reliable.
2. Construction quality is ensured. As the hoist is provided with synchronizer and adjustable function, lifting height can be controlled accurately. Due to above reasons, quality of the tank is ensured.
3. The simple chain type hydraulic jacking system is easy to operate. Construction environment is good and work efficiency is high.
4. The simple chain type hydraulic jacking system is well-adapted. As long as the number of hydraulic hoists is increased or decreased, the whole set of equipment can be applied to the inverted hydraulic lifting construction of large storage tanks with different volumes ranging from several thousand cubic meters to tens of thousands cubic meters.
5. The hydraulic pump station and the hydraulic hoist are placed in the tank for easy operation. Finally, a door-closing plate is reserved to move the equipment out of the storage tank, and the door-closing plate is group welded well.
6. The hydraulic pump station can be controlled singly or jointly, and has strong construction adaptability and excellent technical performance price ratio.
7. Short construction period, low cost and good economic benefit. Due to the high degree of modernization and the fast lifting speed of the complete set of equipment, it has low construction cost and good economic benefit. This technology is truly characterized with convenient and centralized control, simple operation, safety and reliability (no falling), accurate control of weld clearance and lifting height of heavy objects, which can ensure the quality of the project, save labor and reduce costs, and achieve remarkable economic benefits.
Wincoo Engineering Co.,ltd is a hydraulic machinery manufacturing company integrated with design, development, production and sales, which mainly manufactures LYT-type chain-type hydraulic hoist, SQD unfixing holding-latch hydraulic hoist and supporting products. Such products are mainly used for inverted lifting and installation of steel storage tanks. Founded in 2003, after years of concentrated scientific research and development, the company obtained the patent certificate of "Utility Model Hydraulic Hoist' issued by "China National Intellectual Property Administration", and the right to use the trademark of "WINCOO" in 2008, so as to enable products of Wincoo Engineering Co.,ltd to quickly become Chinese brands.
Tank welding machine is actually a transformer with lower external characteristics, which converts 220V and 380V alternating current into low-voltage direct current. Generally, welding machines can be divided into two types according to the output power type, one is AC power and the other is DC.
Here is the content list:
l What is a tank welding machine?
l What are the specific types of tank welding machines?
l Working principle of tank welding machine.
The tank welding machine can be said to be a high-power rectifier. It is divided into positive and negative poles. When AC power is input, it is transformed by a transformer, and then rectified by the rectifier, and then outputs a power supply with reduced external characteristics.
The output terminal is on and off. When it is turned on, a huge voltage change will be generated. When the two poles are short-circuited in an instant, the arc will be ignited. The arc will be used to melt the electrode and the welding material, and the purpose of combining them will be achieved after cooling. Welding transformers have their own characteristics,The external characteristic is the sharp drop in voltage after the electrode is ignited.
1. Light tank welding machine is mainly full rivet type or mixed rivet and welding.
2. The medium tank welding machine is to forge several steel molds, then fill with solder and directly weld.
3. Heavy-duty tank welding machine, the steel plate is forged into a gear staggered shape, first buckled like a button, and then filled with solder, mainly to reduce the burden of the heavy armor on the solder.
The main component of the tank welding machine is a step-down transformer. The two ends of the secondary coil are the work piece and the electrode to be welded. They will ignite the arc during operation and weld the electrode to the gap of the work piece under the high temperature of the arc. Because the iron core of the tank welding machine transformer has its own characteristics, it has the characteristics of a sharp drop in voltage, that is, the voltage drops after the electrode is ignited; when the electrode is short-circuited due to adhesion, the voltage drops sharply.
During the welding operation of the welding machine, although the current in the circuit is equal everywhere, since the resistance is different everywhere, the resistance at the unfixed contact is the largest. According to the law of thermal effect of flow, Q = IRt: When the current is equal, the greater the resistance, the higher the heat generation. Therefore, in the welding process, the contact resistance of the electrode contact point as the contact point of the metal body is the largest, so the electric heat generated in this part is naturally the largest, and the electrode is an alloy with a lower melting point.
The tank welding machine first uses a pulse generating circuit such as a 555 time base circuit to generate a rectangular pulse wave, then uses a transistor for current amplification, and then uses a pair of complementary field-effect transistors for voltage amplification to generate high-frequency signals, and finally uses the transformer with To boost the voltage, and get the induced alternating current on the secondary winding. Its power depends on the amplification capability of the amplifying circuit.
Tank welding machines mostly use single-ended forward inverter circuits composed of IGBT tubes, and most of their control systems use pulse width modulation chip SG3525. The inverter frequency is 20kHz, which can control the external characteristics of constant current.
When the system is at no load, the PWM modulator will output pulses intermittently due to voltage feedback control. Due to the low frequency of intermittent oscillation and narrow pulse width, not only the no-load loss is small, but the transformer is not easily saturated. Because this kind of welding machine adopts the control technology with pulse width modulation PWM as the core.
What is more? WINCOO provide not only tank welding machines, but also pipe spool fabrication solutions for customers from everywhere!