HK-100S tractor is automatic device. It can get wider welding seam after a time welding. It is very suitable for arc welding, the diameter of which is more than 750MM.You can adjust swing speed, swing angle, off-set position of centre and stopping time of left and right. It is suitable for various beads. The biggest speed is 1250mm/min in weldless station.
Automatic CO2 welding trolley is widely used in ships, Bridges, locomotives, steel structures, petrochemical and other industries. Suitable for welding of various welding structures, such as stiffeners, ribs, cross sections, box beams, etc. Its main advantages include:
1, Reduce labor intensity and improve working environment;
2, Improve working efficiency, 1.5 times of manual welding;
3, Avoid the poor welding quality caused by human factors, the general manual operation of the defective rate in about 20%, and the use of automatic welding trolley did not produce welding defective rate, so its comprehensive benefits, than the manual welding increased by nearly 200%;
4, High degree of automation to ensure the stability of welding quality;
| 1 | Weight | 8.4Kg(including wig-wag) | |
| 2 | Size | 430mm×280mm×290mm | |
| 3 | Power supply | DC 24V | |
| 4 | Swing motor | DC 24V | |
| 5 | Driving | Driving of chain gear | |
| 6 | Walking speed | 50~1250mm/min | |
| 7 | Range of blowtorch | Up and down | 40mm |
| Left and right | 120mm | ||
| Job angle adjusting range | ±60° | ||
| Running angle adjusting range | 10° | ||
| 8 | Functions | Walking direction | Fore and after |
| Swing speed | 0~100 | ||
| Left-stop time and right-stop time | 0~2.5 s | ||
| Swing angle | ±15° | ||
| Off-set distance | 0~±8° | ||
| Welding Parameter | ||||
| Welding wire diameter | Φ1.2mm | Φ1.4mm | Φ1.6mm | |
| Current(A) | Down hand welding | 120-300 | 150-380 | 180-430 |
| Flush fillet welding | 120-280 | 150-320 | 180-380 | |
| Horizontal welding | 120-280 | 150-300 | 180-330 | |
| Voltage(U) | U=14+0.051 300A under U=0.041+16±1.50 above 300A U=0.041+20±2.0 | |||
| Distance between nozzle and workpiece(H) | Below 200A: H=10~15mm 200~350A H=15~20mm 350~500A H=20~25mm | |||
| Welding extension length(L) | The length is about 10 times welding wire diameter. It is L=10d | |||
| Packing List | ||
| The contents of the standard package are shown below. Check them carefully before assembling the machine. | ||
| 1 | Complete machine | 1set |
| 2 | The straight rail(1.8 m) | 1set |
| 3 | Standard power wire (16M) | 1set |
| 4 | Fuse(2A) | 2set |
| 5 | Hex wrench | 1pc |
| 6 | Operating manual , Certificate of qualification | 1pc each |
1), This welding trolley is an automatic device, and a wide weld can be obtained by one welding.Especially suitable for welding of arc material (pipe) with radius greater than 900mm.
2), Swing speed, swing Angle, center shift position, and left and right residence time can be adjusted, suitable for different specifications of welding pass. The maximum walking speed of the trolley is 1250mm./min in the state of non-welding.
Ø Note: The self-protection loop switch of the welding machine must be closed OFF when setting and welding, because the welding trolley gas-shielded welder is a constant communication number and the welding inevitably leaves residual ends. If set to ON, the welding trolley will stop moving, but the arc will not be extinguished.
3), The magnet is all on/off control, which is convenient for cleaning iron garbage and moving trolley. The track is controlled to avoid the trolley from the welding line.
4), Arc device is provided, and the arc collecting time adjustment range is 0-7s.
5), The trolley is equipped with an induction stop switch. The trolley can stop automatically after welding, which is convenient for one worker to operate multiple devices at the same time.
6), The installation and disassembly of trolley and track are controlled by special device, which is very convenient to operate
7), Small size, light weight, easy to move and install, unskilled workers can also carry out welding.
HK-100S is made up of body, control case, X-Y slide blocks, blowtorch holder, guide wheel and straight track.
1, Body: It is the driving device, which includes motor, planet reducing box, driving gear and track wheel.
2, Control casing: To control the movement of carriage. Please refer to control panel manual.
3, Cross device: You can use it in the process of straight welding (such as container case) to adjust the position of torch in case of moving track.
4, X-Y trimming slide blocks: It is convenient to adjust the blowtorch up and down or left and right.
5, Swing device: To execute various welding model.
6, Holder of blowtorch: It can hold the blowtorch and adjust the angle of blowtorch easily. Notice: Must not hold the conductive section, which may lead to short out or electric shock.
7, Plug seat of source: It is the plug seat of external electric cable, which is connected with earth wire.This plug seat is in charge of connecting carriage to feeder and supply the power for system. (There are two branches on the end of cable, one of which is used to connect feeder; another is used to connect source.)
Hand knob:It is used to move this machine. Please hold it fully.
On-off hand knob and demount hand knob.
8, Steel belt track: It is equipped with permanent magnet to make the track absorb to works to meet different welding needs. It is very suitable for arc welding, the diameter of which is more than 750MM.
9, Magnet: Strong on-off magnet. If you want to move the track, please turn all magnetron switches "OFF".
10, Cable bracket: You can use it to carry cable to reduce the load of swing machine.
11, Blowtorch: User can choose straight blowtorch or bend blowtorch.
Wincoo Engineering Co., Ltd (WINCOO) is engaged in bringing the most suitable solutions/equipment for client, fabricators, EPC/C companies on pipe fabrication, tank construction, pipeline construction,industrial production lines, clean energy project and other industrial field.
We have ability of providing workable solutions to support clients to be awarded with shorter project execution time, fewer man-hour cost and higher efficiency construction/fabrication method and better quality during phase of project bidding.
Based client's facility/site space availability, we are able to study/design and present matched configurations on project schedule, quality, cost and productivity to guarantee production pace is accordance with project requirement.
To support project execution, we are always ready to work as fireman to give prompt supply on project materials from different consumables, tools, equipment/machines to special merchandise. With flexibility, we are also glad to perform as procurement agent in China to seek required supply resources.
What we can bring to you?
1, Support you to win the project during bidding phase. We can provide your more suitable configurations to help you shorten the constrcution time.
2, We can provide all technical documents and advices to support you for construction procedure clearifications
3, We can support you to calculate the roughly construction time based one welding efficiency, the calculation of manpower needed, welding consumbles quantity
4, We can provide your suitable welding consumbles with much more competetive price from our long time business partner if you need.
5, We can provide site people training service, and operation service or manpower service or as a subcontractor.
Q:Are you a factory or trading company?
A, Yes we are the trading company,but we have a lot of factories that have cooperative relationships, and we can get the best plan and price for you.
Q:Does the machine have CE certificate?
A:Yes, others certifications also can be sent
Q:What's the shipping method?
A: International express and sea transportation,Depend on customer.
Q:Can I use my own forwarder to transport the products for me?
A:Yes, if you have your own forwarder in China, you can let your forwarder ship the products for you.
Q:What's the Payment method?
A:T/T,L/C and other payment method, Depend on customer.
Q: What is our payment term?
A:We can accept the payment by T/T and Trade assueance .
Q: Can you send me the video to show how the machine works?
A: Certainly, we have made video of every machine.
Q: How can I know your machine works well?
A: Before delivery, we shall test the machine working condition for you.And we warmly welcome you to China for inspection.
Q:How to Place an order?
A:Please kinldy send us your order by email,we will confirm the PI with you .
we wish to know the below:your details address,phone/fax number,destination,transportation way;Product informaiton:item number,size,quantity,logo,etc
Sign up for our newsletter to receive the latest news.
Copyright © 2020 WINCOO ENGINEERING CO.,LTD
Support By：Leadong